« previous next »
Pages: [1] 2   Go Down

Author Topic: Stripping & sorting a '53 A10 plunger gearbox  (Read 2747 times)

Offline bakerlonglegs

  • A's Good Friend
  • ***
  • Join Date: Feb 2015
  • Posts: 97
  • Karma: 1
Stripping & sorting a '53 A10 plunger gearbox
« on: 15.05. 2016 22:01 »
The only part of my A10 project in one piece when I got was the gearbox (everything else was in bits).  It's time to strip it down and see what I've got.
Now I've never taken a gearbox apart.  Ever.  Please take anything that follows as potentially rubbish, as I'm learning as I go along. Do feel free to chip in with corrections and observations....   *smile*

What I started with:
Logged

Offline bakerlonglegs

  • A's Good Friend
  • ***
  • Join Date: Feb 2015
  • Posts: 97
  • Karma: 1
Re: Stripping & sorting a '53 A10 plunger gearbox
« Reply #1 on: 15.05. 2016 22:27 »
First, off with the outer cover.  Four, rather chewed, nuts and three screws later, all to be replaced, and it comes away thankfully easy.  Underneath there is the speedo drive, the clutch actuating arm, the kickstart spindle and quadrant, and the gear change selector lever, all OK.  The selector lever is bit loose on the spindle, I may peal the tab washer back and see if it can be tightened. 
Logged

Offline bakerlonglegs

  • A's Good Friend
  • ***
  • Join Date: Feb 2015
  • Posts: 97
  • Karma: 1
Re: Stripping & sorting a '53 A10 plunger gearbox
« Reply #2 on: 15.05. 2016 22:38 »
Looking at the kickstart ratchet mechanism on the end of the main shaft, to my untrained/inexperienced eyes the teeth look rather worn.  The tab washer looks like it's been off a few times, time for a new one of those too.
Logged

Offline bakerlonglegs

  • A's Good Friend
  • ***
  • Join Date: Feb 2015
  • Posts: 97
  • Karma: 1
Re: Stripping & sorting a '53 A10 plunger gearbox
« Reply #3 on: 15.05. 2016 22:44 »
The inner cover comes away with some gentle taps.  (I have replacement gaskets already!)
Logged

Online trevinoz

  • Newcastle, N.S.W. Australia.
  • Wise & Enlightened
  • *
  • Join Date: Jul 2006
  • Posts: 3234
  • Karma: 71
Re: Stripping & sorting a '53 A10 plunger gearbox
« Reply #4 on: 15.05. 2016 22:50 »
Now loosen the grub screw on the drive end and remove the selector shaft. Then lift out the cluster after taking out the main shaft.
Logged

Offline bakerlonglegs

  • A's Good Friend
  • ***
  • Join Date: Feb 2015
  • Posts: 97
  • Karma: 1
Re: Stripping & sorting a '53 A10 plunger gearbox
« Reply #5 on: 15.05. 2016 22:53 »
After taking out the grub screw holding the gear shifter shaft, I could take out the main and lay shaft gear clusters.  As this is my first gearbox strip down I don't quite know what I'm looking for but, with one exception, they look OK to me.

Edit:  thanks Trev!  More to come....
Logged

Offline bakerlonglegs

  • A's Good Friend
  • ***
  • Join Date: Feb 2015
  • Posts: 97
  • Karma: 1
Re: Stripping & sorting a '53 A10 plunger gearbox
« Reply #6 on: 15.05. 2016 23:00 »
The exception is this gear on the end of the layshaft.  The inside slots are rounded off.  I think it's because the layshaft thrust washer had been assembled on the wrong side of the gear during a rebuild by a former owner, meaning the gear caught on the lugs (right word?) of the adjacent gear when the 'box was in neutral.  Might look at replacing this if I can. 
Logged

Offline bakerlonglegs

  • A's Good Friend
  • ***
  • Join Date: Feb 2015
  • Posts: 97
  • Karma: 1
Re: Stripping & sorting a '53 A10 plunger gearbox
« Reply #7 on: 15.05. 2016 23:05 »
Now to the clutch end of things.  I followed the Haynes advice and clamped an old chain round the gearbox sprocket to hold it still while I took the nut off.  The teeth on the sprocket have looked better and one has cracked, so that's another part to replace.

That's all for now, more tomorrow....
Logged

Offline RichardL

  • Outside Chicago, IL
  • Wise & Enlightened
  • *
  • Join Date: Nov 2007
  • Posts: 6483
  • Karma: 55
Re: Stripping & sorting a '53 A10 plunger gearbox
« Reply #8 on: 16.05. 2016 00:11 »
Quote from: bakerlonglegs on 15.05. 2016 22:44
The inner cover comes away with some gentle taps.  (I have replacement gaskets already!)

Looking at the picture that ends in 580, there appears to be cracks around one of the holes. I believe it's the hole for the gear shifter fork shaft.

Richard L.
Logged

Offline bakerlonglegs

  • A's Good Friend
  • ***
  • Join Date: Feb 2015
  • Posts: 97
  • Karma: 1
Re: Stripping & sorting a '53 A10 plunger gearbox
« Reply #9 on: 16.05. 2016 08:30 »
RichardL - you're right, there are cracks around that hole  *sad2* . I'll need to think about repair, if there's any way of doing that, or replacement.
Logged

Offline duTch

  • Ricketty Rocketty Golden Flashback
  • Wise & Enlightened
  • *
  • Join Date: Oct 2011
  • Posts: 4528
  • Karma: 41
Re: Stripping & sorting a '53 A10 plunger gearbox
« Reply #10 on: 19.05. 2016 11:28 »

 
Quote
RichardL - you're right, there are cracks around that hole  *sad2*

 Strange place for stress cracks *dunno*...

 BLL;- As you've no doubt discovered these boxes are fairly user friendly. To my inexperienced eye it all looks better than some of mine except for some 'chattering'  on the teeth and the 'H' (1st l/s)gear.

 The bottom rear mounts look a bit flogged, I got around this by tidying them up (filing them square), and fitting the box to frame with the top mount bolt in and adding some S/S washers under them to take up the slop. This can be also achieved by building up with weld and fettling.

 Obviously you'll check for any wear /slop in the layshaft bushes? A bit hard to determine easily due to lack of access.
 
 good luck, help is at hand
Logged
Started building in about 1977/8 a on average '52 A10 -built from bits 'n pieces never resto intended -maybe 'personalised'
Have a '74 850T Moto Guzzi since '92-best thing I ever bought doesn't need a kickstart 'cos it bump starts sooooooooo(mostly) easy
Australia

Offline Topdad

  • bob hebdon
  • Wise & Enlightened
  • *
  • Join Date: May 2011
  • Posts: 2655
  • Karma: 36
  • l
Re: Stripping & sorting a '53 A10 plunger gearbox
« Reply #11 on: 19.05. 2016 16:03 »
If you need any parts send me a PM as I've got a box of gearbox bits which include a lot of plunger stuff ,no interest to me as mines a s/wing arm . Bob
Logged
" rules are made for the guidance of wise men and the blind obediance of fools"
United Kingdom

Offline bakerlonglegs

  • A's Good Friend
  • ***
  • Join Date: Feb 2015
  • Posts: 97
  • Karma: 1
Re: Stripping & sorting a '53 A10 plunger gearbox
« Reply #12 on: 19.05. 2016 22:38 »
duTch - thanks for the advice!

Topdad - cheers! PM on the way, I just need to check the part number.
Logged

Online Joolstacho

  • Wise & Enlightened
  • *
  • Join Date: Jan 2010
  • Posts: 1193
  • Karma: 7
Re: Stripping & sorting a '53 A10 plunger gearbox
« Reply #13 on: 20.05. 2016 00:31 »
Quote from: bakerlonglegs on 15.05. 2016 23:00
The exception is this gear on the end of the layshaft.  The inside slots are rounded off.  I think it's because the layshaft thrust washer had been assembled on the wrong side of the gear during a rebuild by a former owner, meaning the gear caught on the lugs (right word?) of the adjacent gear when the 'box was in neutral.  Might look at replacing this if I can.
Long time since I've had my 'box apart but I think those 'slots' are meant to be like that, to make it easier for the matching 'pegs' to engage.
Someone with a better memory please confirm or otherwise.
Logged

Offline bakerlonglegs

  • A's Good Friend
  • ***
  • Join Date: Feb 2015
  • Posts: 97
  • Karma: 1
Re: Stripping & sorting a '53 A10 plunger gearbox
« Reply #14 on: 21.05. 2016 10:03 »
Time for some more pics....

Circlip and oil removed.  The bearing seems OK, but is that one of those parts that you should always replace when rebuilding an old gearbox?

Logged
Pages: [1] 2   Go Up
« previous next »